Basic Information:
Name: DOIO HITPAD Compact Series
Firmware: GP2040-CE
Product Link: Here
Instructions:
Default Keys
Mode Selection
Input mode
To select an input mode, Press and hold one of the following buttons before connecting the device.
1P-PS3 /D-Input (RaspberryPi/Android)1K-Nintendo Switch
2K-PC /X-Input (Windows/Steam)
2P-PS4 Mode
*PS4 and PS5 require Magicboots or other converters, Magicboots MUST be purchased separately.
Orientation Mode
SELECT+START+DOWN ARROW = Visual helmet mode(DP)
SELECT+START +LEFT ARROW = Left-analog stick
SELECT+ START+RIGHT ARROW = Right analog stick
SELECT+START +LEFT ARROW = Left-analog stick
SELECT+ START+RIGHT ARROW = Right analog stick
SOCD Mode
HOME + START+DOWN ARROW = Neutral (up+down=middle, left+right=middle )
HOME + START+UP ARROW = SOCD1 (up+down=up, left+right = middle)
HOME+START+LEFT ARROW= Last input priority (post-override)
RGB Mode
SELECT+ START+1P = Next AnimationSELECT + START +1K = Previous Animation
SELECT+ START +2P = Brightness Up
SELECT+START+2K = Brightness Down
SELECT+ START +3P =Switch to Next Lighting Preset
SELECT+ START +3K = Switch to Previous Lighting Preset
SELECT+ START+4P = Next Key Triggers Light Color
SELECT+ START+4K = Previous Key Triggers Light Color
Rapid Fire Mode
Press and hold the TURBO button, then press the button you want to set for continuous shooting. Holding the button will be recognized as rapid shooting. After set, you can cancel rapid fire by repeating the same action.
Rapid fire can be set for 1P, 2P, 3P, 4P, 1K, 2K, 3K, or 4K, across 8 buttons.The firing rate can be adjusted within the range of 1 to 60 shots per second (individual button firing rate adjustment is not supported).
Hold the TURBO button and press the UP key to increase the firing rate, or hold the TURBO button and press the DOWN key to decrease it.
Even if the power is turned off, the set firing rate will be saved, but the rapid fire button status will be cleared.
key Mapping
|
Keys/Modes
|
XINPUT
|
SWITCH
|
PS3
|
DINPUT
|
GP2040
|
|
1P
|
X
|
Y
|
■
|
1
|
B3
|
|
2P
|
Y
|
X
|
▲
|
4
|
B4
|
|
3P
|
RB
|
R
|
R1
|
6
|
R1
|
|
4P
|
LB
|
L
|
L1
|
5
|
L1
|
|
1K
|
A
|
B
|
×
|
2
|
B1
|
|
2K
|
B
|
A
|
〇
|
3
|
B2
|
|
3K
|
RT
|
ZR
|
R2
|
8
|
R2
|
|
4K
|
LT
|
ZL
|
L2
|
7
|
L2
|
|
SELECT
|
BACK
|
-
|
SELECT
|
9
|
S1
|
|
START
|
START
|
+
|
START
|
10
|
S2
|
|
LS
|
LS
|
LS
|
L3
|
11
|
L3
|
|
RS
|
RS
|
RS
|
R3
|
12
|
R3
|
|
HOME
|
XBOX
|
HOME
|
13
|
A1
|
|
|
TP
|
SCREENSHOT
|
14
|
A2
|
Changing Key Values
We recommend prioritizing key remapping within the game. If the function cannot be achieved, please use the following features.
Press and hold the Start button before connecting the Type-C cable. Click http://192.168.7.1/ to access the debug page.Click on "Configuration" and select "Pin Mapping."
Each pin corresponds to a specific key value. Such as changing the UP key to the L1 position, Setting PIN 02 to "L1" and PIN 13 to "UP.". Save to apply.
Save up to 4 different key value sets under "Profile 1~4" at the top. To set a specific set of key values, click the "Map buttons with switch" , select it and click the "Save" button.
Pin Number
Switching to PS4 Mode and Avoiding 8-Minute Timeout
Access the debug page, click the “Settings” button at the top to enter Input Mode Setting, and select “PS4” from the “Current Input Mode” dropdown.In the Authentication Settings, choose “Uploaded Key File” and upload the three required files. Click “Verify and Save” in the bottom right to save.
In the top right corner of the webpage, switch to PS4 mode, then click "Reboot - Controller".
* Files are not provided directly.
To add a new user: Press the Home key, a page will appear, click "Add User"
Switching to PS5 Mode
Access the debug page, click the “Settings” button at the top, and select “PS5” from the “Current Input Mode” dropdown.In the Authentication Settings，select "Host USB" and click "Save."
Click on "Configuration" and select "Peripheral mapping" . Enable "USB Host" function, set "D+" to "26." and click "Save."
Note:To add a new user: Press the Home key, a page will appear, click "Add User"
Switch XBOX Mode
Click on "Configuration" and select "Peripheral mapping" . Enable "USB Host" function, set "D+" to "26." and click "Save."Access the debug page, click the “Settings” button at the top, and select “XBOX One” from the “Current Input Mode” dropdown, then click "Save."
Connect the XBOX device verifier to start using it.
Switching Keyboard Mode
Access the debug page, click the “Settings” button at the top, and select “Keyboard” from the “Current Input Mode” dropdown, then click "Save."Click on "Configuration" and select "Peripheral mapping" , Enable "USB Host" function, set "D+" to "26." and click "Save."
Configure Custom Lighting Theme
Click on "Configuration" and select "Custom LED Themes."Click the "Enable" button, then set the colors for Normal and Pressed lights by clicking the corresponding buttons.
Click "Save," then reconnect the Type-C cable to apply the changes.
Firmware Upgrade
Hold the button on the back of the device, connect the Type-C cable, then release the button. A new disk named "RPI-RP2" should appear on your computer, double-click to enter.
Drag the “flash_nuke.uf2” file to the “RPI-RP2” disk. The disk will disappear and reappear after 5-10 seconds.
Drag the “GP2040-CE_0.7.9_Pico.uf2” file into the “RPI-RP2” disk. Wait for the transfer to complete. The device’s screen will light up, indicating that the firmware update is complete.
Drag the “flash_nuke.uf2” file to the “RPI-RP2” disk. The disk will disappear and reappear after 5-10 seconds.
Drag the “GP2040-CE_0.7.9_Pico.uf2” file into the “RPI-RP2” disk. Wait for the transfer to complete. The device’s screen will light up, indicating that the firmware update is complete.
